77 lines
2.5 KiB
ObjectPascal
77 lines
2.5 KiB
ObjectPascal
|
#!/bin/sh
|
||
|
|
|
||
|
|
#
|
||
|
|
# Note: The adapter shell var must updated in order to reflect your actual hardware.
|
||
|
|
# The current value "friq" is the right value for the FreeCom PP adapter.
|
||
|
|
# See paride documentation for the list of other drivers.
|
||
|
|
#
|
||
|
|
adapter=friq
|
||
|
|
|
||
|
|
case "$1" in
|
||
|
|
|
||
|
|
'start')
|
||
|
|
echo "Starting Parallel Port IDE/ATAPI"
|
||
|
|
modprobe paride
|
||
|
|
modprobe "$adapter"
|
||
|
|
# modprobe pg
|
||
|
|
# modprobe pg verbose=2 drive0=0x378,0,0,-1,-1,0
|
||
|
|
modprobe pg verbose=0 drive0=0x378,0,0,-1,-1,0
|
||
|
|
;;
|
||
|
|
|
||
|
|
'stop')
|
||
|
|
echo "Stopping Parallel Port IDE/ATAPI"
|
||
|
|
rmmod pg
|
||
|
|
rmmod "$adapter"
|
||
|
|
rmmod paride
|
||
|
|
;;
|
||
|
|
|
||
|
|
*)
|
||
|
|
echo "Usage: rc.pp start|stop"
|
||
|
|
esac
|
||
|
|
|
||
|
|
exit
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
When you load pg, you need to specify some parameters like:
|
||
|
|
|
||
|
|
drive0=0x378,0,0,4,0,0
|
||
|
|
|
||
|
|
The parameters are:
|
||
|
|
|
||
|
|
<prt>,<pro>,<uni>,<mod>,<slv>,<dly>
|
||
|
|
|
||
|
|
Where,
|
||
|
|
|
||
|
|
<prt> is the base of the parallel port address for
|
||
|
|
the corresponding drive. (required)
|
||
|
|
|
||
|
|
<pro> is the protocol number for the adapter that
|
||
|
|
supports this drive. These numbers are
|
||
|
|
logged by 'paride' when the protocol modules
|
||
|
|
are initialised. (0 if not given)
|
||
|
|
|
||
|
|
<uni> for those adapters that support chained
|
||
|
|
devices, this is the unit selector for the
|
||
|
|
chain of devices on the given port. It should
|
||
|
|
be zero for devices that don't support chaining.
|
||
|
|
(0 if not given)
|
||
|
|
|
||
|
|
<mod> this can be -1 to choose the best mode, or one
|
||
|
|
of the mode numbers supported by the adapter.
|
||
|
|
(-1 if not given)
|
||
|
|
|
||
|
|
<slv> ATAPI devices can be jumpered to master or slave.
|
||
|
|
Set this to 0 to choose the master drive, 1 to
|
||
|
|
choose the slave, -1 (the default) to choose the
|
||
|
|
first drive found.
|
||
|
|
|
||
|
|
<dly> some parallel ports require the driver to
|
||
|
|
go more slowly. -1 sets a default value that
|
||
|
|
should work with the chosen protocol. Otherwise,
|
||
|
|
set this to a small integer, the larger it is
|
||
|
|
the slower the port i/o. In some cases, setting
|
||
|
|
this to zero will speed up the device. (default -1)
|
||
|
|
|
||
|
|
EPP mode is best. Your BIOS may not give you that option, unfortunately.
|
||
|
|
What options does it support ?
|