70 lines
2.3 KiB
Plaintext
70 lines
2.3 KiB
Plaintext
#ident @(#)cdrecord.dfl 1.8 14/01/03 Copyr 1998-2014 J. Schilling
|
|
#
|
|
# This file is /etc/default/cdrecord
|
|
# It contains defaults that are used if no command line option
|
|
# or environment is present.
|
|
#
|
|
# The default device, if not specified elswhere
|
|
# Note that since Sommer 2006, cdrecord by default searches for a
|
|
# single CD-ROM device. You should set CDR_DEVICE= together with
|
|
# an entry in the device table below only if you have more than
|
|
# one CR-ROM drive in your system.
|
|
#
|
|
#CDR_DEVICE=yamaha
|
|
#CDR_DEVICE=default
|
|
|
|
#
|
|
# The default speed (speed=), if not specified elswhere
|
|
#
|
|
# Note that newer cdrecord versions do not default
|
|
# to speed=1. For MMC compliant drives, the default
|
|
# is to write at maximum speed, so it in general does
|
|
# not make sense to set up a default speed in /etc/default/cdrecord
|
|
#
|
|
#CDR_SPEED=40
|
|
|
|
#
|
|
# The default FIFO size (fs=), if not specified elswhere
|
|
#
|
|
#CDR_FIFOSIZE=16m
|
|
|
|
#
|
|
# The default transfer size (ts=), if not specified elswhere
|
|
# The cdrecord default transfer size (currently) is 63k because
|
|
# Linux and Solaris have problems with bigger transfer sizes.
|
|
# If you are on FreeBSD, it is recommened to set CDR_TRANSFERSIZE=126k
|
|
#
|
|
#CDR_TRANSFERSIZE=32k
|
|
|
|
#
|
|
# The following definitions allow abstract device names.
|
|
# They are used if the device name does not contain the
|
|
# the characters ',', ':', '/' and '@'
|
|
#
|
|
# Unless you have a good reason, use speed == -1 and let
|
|
# cdrecord use it's intercal drive specific defaults.
|
|
#
|
|
# Call cdrecord -scanbus to find the right "device name" for your
|
|
# drive. Then set up a list entry with an arbitraty logical name,
|
|
# followed by the SCSI device name of the drive. If speed or fifosize
|
|
# should stay with the defaults, insert a -1. If you do not need to
|
|
# set driveropts, use an empty string. The transfer size entry may be omitted.
|
|
# It is recommended to set "burnfree".
|
|
#
|
|
# The logical device name must be followed by an equal sign, the fields may
|
|
# be separated by one or more tab or space.
|
|
#
|
|
# drive name device speed fifosize driveropts transfersize
|
|
#
|
|
my-default= 1,0,0 -1 -1 burnfree 63k
|
|
sol-default= USCSI:1,0,0 -1 -1 burnfree
|
|
ricoh-u= USCSI:0,2,0 -1 -1 burnfree
|
|
teac= 1,3,0 -1 -1 ""
|
|
teac-max-ts= 1,3,0 -1 -1 "" 32k
|
|
panasonic= 1,4,0 -1 -1 ""
|
|
plextor= 1,4,0 -1 -1 ""
|
|
sanyo= 1,4,0 -1 -1 burnfree
|
|
yamaha= 1,5,0 -1 -1 ""
|
|
cdrom= 0,6,0 2 1m ""
|
|
remote= REMOTE:rscsi@somehost:1,0,0 16 16m burnfree
|